Skip to content Skip to navigation menu
HGH30CAZ0H
Type:
HGH30CAZ0H
Article number:
5-001671

Wymiary montażowe

Momenty

Dimensions
H Total height 45 mm
H1 6 mm
N 16 mm
W Block width 60 mm
B 40 mm
B1 10 mm
C 40 mm
L1 70 mm
L Block length 97,4 mm
K1 20,25 mm
K2 6 mm
G 12 mm
M M8
l 10 mm
T 8,5 mm
H2 9,5 mm
H3 13,8 mm
Mass 0,88 kg
Load ratings and torques
Cdyn Dynamic load rating 48500 N
C0 Static load rating 71870 N
M0X Static moment 660 Nm
M0Y Static moment 700 Nm
M0Z Static moment 700 Nm
Static load rating C0
If a linear guideway system is subjected to excessive loads or impacts during movement or at a standstill, localised permanent deformation occurs between the track and balls. As soon as this permanent deformation exceeds a certain level, it affects smooth operation of the guideway. According to its basic definition, the static load rating corresponds to a static load that causes permanent deformation of 0.0001 × ball diameter at the contact point that is loaded the most. The values are given in the tables for each linear guideway system. Using these tables, the designer can select a suitable linear guideway system. The maximum static load to which a linear guideway system is subjected must not exceed the static load rating.

Permissible static moment M0
The permissible static moment is the moment which, in a defined direction and size, corresponds to the maximum possible load on the moving parts by the basic static load rating. The permissible static moment is defined for linear motion systems for three directions: MX, MY and MZ.

Solid steel block SE
For continuous operation at temperatures above 80 °C, solid steel blocks with steel deflection systems are used. The standard end seals are replaced by heat-resistant end seals and the plastic cover caps of the profile rail by brass cover caps.

Long-time lubrication unit E2
The long-time lubrication unit considerably increases lubrication intervals. Depending on the application and ambient conditions, it can achieve lifetime lubrication. It also considerably reduces lubricant consumption, as only the required quantity of lubricant is applied. The compact construction and special design allows the block to be fitted in any position without impairing the lubrication function. The long-time lubrication unit can be used at ambient temperatures of -10°C to +60°C.

HIWIN coating HICOAT CZS
HICOAT CZS is a very thin zinc coating that offers a very good corrosion protection, even on radii and chamfers. Smaller bare parts stay protected by the cathodic corrosion protection. Compared with uncoated pieces this leads to significantly higher periods of use. The CZS coating is available for the HG, EG and CG series. Further information can be found in the catalogue "Linear Guideways" under chapter "HIWIN coatings for linear guideways".

HIWIN coating HICOAT CTS
HICOAT CTS is a thin layer chrome coating that offers good corrosion protection and a very high wear protection. The high wear protection results from the extraordinary hardness of the coating. The CTS coating is free of Cr(VI) and suitable for use in food stuffs. It is available for the HG, EG, CG and WE series. Further information can be found in the catalogue "Linear Guideways" under chapter "HIWIN coatings for linear guideways".

Name Article number Description  
HG-30-SS 5-000074 Standardabdichtung  
HG-30-DD 5-001828 Doppelte Enddichtung  
HG-30-ZZ 5-000066 Enddichtung mit Blechabstreifer  
HG-30-KK 5-001835 Doppelte Enddichtung mit Blechabstreifer  
HG-30-SW-C 5-001840 Enddichtung mit Doppellippe  
HG-30-ZWX-C 5-000020 Enddichtung mit Doppellippe und optimiertem Blechabstreifer  
HG-30-SSL 5-003152 Leichtlaufdichtung  
Name Article number Description  
HG-30-E2-KIT-SS 5-001831 Langzeit-Schmiereinheit zur Verlängerung der Nachschmierintervalle  
HG-30-E2-KIT-DD 5-001829 Langzeit-Schmiereinheit zur Verlängerung der Nachschmierintervalle  
HG-30-E2-KIT-ZZ 5-001832 Langzeit-Schmiereinheit zur Verlängerung der Nachschmierintervalle  
HG-30-E2-KIT-KK 5-001830 Langzeit-Schmiereinheit zur Verlängerung der Nachschmierintervalle  
Name Article number Description  
HGR30R4000H 5-001926 Profilschiene  
HGR30R4000C 5-001957 Profilschiene  
HGR30T4000H 5-001995 Profilschiene  
HGR30T4000C 5-001974 Profilschiene  
Name Category Product Size Language
Prowadnice liniowe CG Ulotka Prowadnice z szyną profilową 301 KB
Prowadnice z szyną profilową Formularz projektowy Prowadnice z szyną profilową 2 MB
Prowadnice z szyną profilową Katalog Prowadnice z szyną profilową 7 MB
Prowadnice z szyną profilową Instrukcja montażu Prowadnice z szyną profilową 5 MB
Go to download centre
Prowadnica z szyną profilową – smarowanie smarem przez gniazdo smarowe
Ten film wideo pokazuje, jak mozna montowac adapter smarowniczki na wózku prowadnicy z szyna profilowa. Dzieki temu naklady na smarowanie sa redukowane do minimum. Srodki smarne zasadniczo zmniejszaja zuzycie, chronia element przed zabrudzeniem i tym samym wydluzaja okres uzytkowania. Smar jest elementem konstrukcyjnym i z tego wzgledu nalezy go uwzglednic juz na etapie projektu maszyny. Prowadnice z szyna profilowa HIWIN potrzebuja, jak kazde lozysko toczne, wystarczajacego zaopatrzenia w smary. W zasadzie mozliwe jest w tym przypadku zarówno smarowanie smarem stalym jak i olejem.

Jednostka smarowania długotrwałego prowadnicy z szyną profilową
Jednostka smarowania dlugotrwalego dla prowadnic z szyna profilowa umozliwia wielokrotne zwiekszanie okresów miedzy smarowaniami i tym samym znaczne zmniejszenie czestotliwosci konserwowania. W zaleznosci od potrzeb mozliwe jest zamontowanie az dwóch jednostek smarowania dlugotrwalego na wózek.
Montaż i demontaż osłon
Zaslepki sluza do zabezpieczania otworów montazowych szyn profilowych przed wiórami i zanieczyszczeniem. Ten film wideo pokazuje, jak latwo mozna montowac i demontowac nakladki stalowe, mosiezne lub wykonane z tworzywa sztucznego.
Sposób działania prowadnicy z szyną profilową
Prowadnica z szyna profilowa umozliwia liniowe przemieszczanie za pomoca rolek. Dzieki zastosowaniu kulek lub rolek miedzy szyna a wózkiem mozna osiagnac bardzo precyzyjny ruch liniowy prowadnicy z szyna profilowa.
Opór przesuwu w zależności od stanu smarowania
Opór przesuwu wózka zalezy od wielu czynników, np. obciazenia, temperatury, smaru (smar staly, smar plynny, olej), ilosci smaru, predkosci przesuwu, serii, wielkosci lub systemu uszczelnienia. Podanie konkretnego oporu przesuwu jest wiec mozliwe tylko przy okreslonych warunkach ramowych. Istotnym czynnikiem jest tutaj smar i stan smaru. Szczególnie przy swiezym smarowaniu znacznie wzrasta opór przesuwu. Jednak juz po 15-metrowej fazie dotarcia opór przesuwu zmniejsza sie o ok. 50%.

Fazowanie maszynowe lub ręczne
Ten film wideo pokazuje, jak dziala maszynowe i reczne fazowanie krawedzi przy prowadnicach z szyna profilowa.